Self-priming magnet drive centrifugal pump SLM DV
Design features
- Process oriented design
- Self-priming, transports gas
- Magnet drive
- Leakproof
- Horizontally mounted
- Modular system
- Ducted impeller
- Thermal barrier
- Secondary seal
- Oiled ball bearing
Technical data
Q up to 450 m3/h with 50Hz / up to 540 m3/h with 60Hz
H up to 60 m with 50Hz / up to 85 m with 60Hz
t from -20 °C up to +120 °C
p up to PN 16
Special constructions and
higher outputs available.
Materials
Standard construction
Pump casing: 316 SS or GGG 40.3
Impeller: 316 SS or nodular iron or GGG 40.3
Isolation shell: 316 Ti/Hastelloy C4
Magnet carrier: 316 Ti
Internal bearings: silicon carbide
Bearing lantern: nodular iron
Bearing carrier: ductile iron
Other materials available
Identification code:
Bearing carrier realizations:
| Bearing carrier | Realization | Comments |
| SLM DVS | Standard | Greased, with deep groove ball bearing |
| SLM DVO | Standard | ??lschmierung mit verl?¤ngertem W?¤lzlagerabstand |
Close-coupled realization:
| Variants | Realization | Comments |
| SLM DVB | Close coupled configuration | Motor carrier (without shaft coupling) |
Suffixes (designs):
| H1 | heated pump casing |
| H2 | jacketed bearing lantern |
| S | thermal barrier without secondary seal |
| W | thermal barrier with secondary seal |
| F | internal filter |
| Z, C | isolation shell made of zirconium oxide (Z); isolation shell with CFK plastic cladding (C) |
| E1 | external feeding, internal secondary-flow boring enclosed |
| E2 | external flushing and venting; internal secondary-flow boring non-enclosed |
| E1F | external secondary flow with main flow filter per DGRL |
| OT | pump without secondary flow (see description of SLM NV OT) |
| D | double isolation shell |
Design variants
Heated pump H1 and/or H2
The pumps are outfitted with a heat jacket and pump casing (H1) and/or a heat jacket in the bearing lantern (H2). Both heat jackets can be realized either separately or in conjunction with a bypass line. The heat jackets in the standard construction are rated for operating pressure of 16 bar at 200 ?°C (steam) or 6 bar at 350 ?°C. The heat jackets can also be used for cooling.
S or W thermal barrier and secondary seal
The thermal barrier acts as a structural element between the bearing carrier (in the bearing carrier model) or drive motor (in the close coupled model), whereas the hydraulic system allows for heat transfer. This reduces ball bearing temperatures in the gearing when hot liquids are being transported. A radial shaft sealing ring can also be integrated into the thermal barrier for purposes of sealing the magnet driver. The sealing ring acts as a secondary seal that prevents the product from leaking into the environment through a leak in the isolation shell. In order for this secondary seal to be used, the magnet driver chamber must be monitored so that leaks can be detected in good time.
Internal filter F
When solids-containing liquids are being transported, the internal filter prevents inadmissibly large particles from entering the flow channels, and from there the magnetic coupling and internal bearings.
External feed and flushing connections E1 and E2
These external connections allow for external flushing, feeding and/or venting. Connection E1 is used in situations where a continuous feed into the magnet drive is desired. Connection E2 is used suitable for short-term flushing, or for external venting of the magnetic coupling.
Double isolation shell D
The double isolation shell should be used in situations requiring a high level of safety. The unit consists of two interlocking isolation shells, both of which are rated for the relevant operating conditions. If one of the two units is damaged, the casing still remains leaktight. The gap between the two units can be monitored.
